What to do first - wallpaper, laminate or doors? What comes first - laminate or doors: looking for the optimal solution What comes first - doors or laminate.

One of the most important points during repairs is to do everything in a certain sequence. Often a mistake made here then turns into quite serious consequences. However, this point is often the subject of controversy. For example, quite often the question arises: what do they do first - glue wallpaper or install interior doors?

Let's look at this situation more seriously. Surely everyone knows that in a room covered with wallpaper, the level of humidity seriously increases. Moreover, this process does not tolerate drafts. If you are planning to change your front doors, the question of what to do first can puzzle many. Indeed, the absence of doors may well provoke such an unwanted draft. However, this problem can be solved by simply closing all windows. At the same time, they try to open the entrance doors as rarely as possible.

On the other hand, if you put the doors first, then due to high humidity, the frame and the canvas, in the absence of a protective layer, may well swell. Accordingly, the answer to the question that interests us in this case is obvious - first of all, you need to hang the wallpaper, and only after that should you install the doors. However, here I would like to make a small clarification. Replacing doors should be approached with all responsibility.

In particular, it is recommended to first call a measurer so that you know all the required dimensions and do not make a mistake when purchasing. If you have the necessary knowledge, then you can do it yourself. Next, make sure that the width and height of the opening remain unchanged. If you move it to another place, be sure to ensure that the dimensions match. After the wallpaper is glued, you can put the box and hang the canvas. Don't forget that the foam must dry well. During this period, the opening is strengthened with spacers. It is better not to touch the canvas again while it is drying, so as not to provoke distortion. In the end, you just need to remove the excess foam with a knife and attach the trim.

We have sorted out the question of what needs to be done first - gluing wallpaper or installing doors. However, I would also like to consider the procedure for repairs in general. Here the sequence is very simple:

• ceiling;
• walls;
• door installation.

In other words, work is performed from top to bottom. This approach makes it possible to obtain an almost 100 percent guarantee that already repaired areas will not be damaged in any way during the finishing process of the next ones. However, one very important clarification is worth making here. If you plan to completely tear down the floor and pour a cement screed, then the work will need to start from the bottom.

In all other cases, the ceiling is done first. The most common options are drywall, tension board, or a combination of both. After the ceiling is done, you can start working on the walls. The material for leveling here is selected depending on their curvature. Often, putty is enough - starting and finishing. But if the walls are very crooked, then you can’t do without plaster. The best option is, of course, to completely rip everything off, to the ground. After this, apply a layer of plaster and then level it with putty. First, the starting one is applied, then the finishing one.

Do not forget that each layer must dry thoroughly. There's no need to rush here. The thing is that modern wallpaper has a non-woven base. Accordingly, moisture that has not had time to dry will come out on top of the layer of finishing putty. She will have nowhere else to go. The thing is that the base of the wallpaper does not allow moisture to pass through. Accordingly, mold forms on the wall. Ultimately, its spores will still leak through the non-woven fabric onto the surface of the wallpaper, and everything will have to be redone.

If you decide to lay laminate, linoleum or parquet on the floor without pouring a screed, then first of all it is recommended to level the surface using OSB boards. It is best to do this while the putty is drying - this way you will not lose much time. If the work is done by several craftsmen, then you can glue wallpaper and, say, lay laminate flooring at the same time. One works against one wall, the other works against the opposite wall. And finally, finishing work. This is the installation of interior doors (frames and leaves), baseboards, and the very last stage - attaching the trim.

In some cases, due to certain circumstances, the sequence of work may differ slightly from that described above. However, this scheme is considered the most optimal. Many craftsmen make repairs in exactly this sequence. Of course, we have not mentioned many more mandatory steps - dismantling old coatings, laying new wiring and communications, installing plumbing. However, then the description of the entire sequence would be too long. In addition, there are also a number of purely individual factors.

When undertaking renovation work on a house, many owners are at a loss. At the initial stage and during the process itself, many questions arise, especially during the period of interior finishing work. To make work easier and streamline all actions, you should develop a plan in which each stage is clearly distributed. It will help you avoid making mistakes and save time, nerves and money.

Finishing stages

So, when starting to decorate the premises, it is worth familiarizing yourself with the sequence in which the work should be carried out. As mentioned earlier, such an approach will help to complete the repair quickly enough and avoid various shortcomings, and, consequently, their correction.

Main finishing stages:

• The main direction of work is top to bottom. In other words, the standard practice is to finish the ceiling first, then the walls, and finally the floor. This unusual principle serves to preserve ready-made parts of the room from damage during processing and installation of other areas.
• If a floor screed is required before laying the finished floor covering, do it first. A screed is an intermediate layer that serves as a base for the floor covering, adding rigidity to it, and hiding communications. The better it is made, the longer the coating will last. Screeds vary in composition, method of adhesion and installation, as well as purpose.
• You can level the walls using plaster. Depending on the original condition of the walls, one or more layers may be needed. Before plastering, the walls must be primed to improve the condition of the surface and subsequently the paint will adhere better.
• Finally, at the end of preparing the walls, they are puttied. All irregularities and communication points are carefully sealed. The walls are prepared for finishing.

• Installation of door frames. The door can be installed immediately and covered with thick polyethylene to protect it from dirt and mechanical damage.
• Cover the walls with wallpaper;
• Laying finishing flooring (laminate, linoleum, parquet).
• Fastening ceiling plinths, decorative elements, switches, sockets and trim.

Repair work should begin from the furthest rooms and move towards the exit. The finishing of the corridor and hallway is carried out at the very end. All this will prevent dirt and dust from getting into the finished rooms, as well as damage to fresh coatings.

Having finished one room, the door leading into it is closed and curtained with thick plastic film. This will protect clean finishing materials from dirt, dust, paint or plaster.

Installing doors before laminate

What should the laminate or doors be laid first?
If the doors are to be installed initially, then you must immediately decide what thickness of the laminate will be used and what material the backing will be made of. These parameters will determine how much the floor will rise from the rough to the finishing level. Only after this can you order doors, knowing the exact height of the door frame. When installing, the bottom is often filed down so that there is space at the bottom for the substrate, insertion of the laminate under the box, and there is also an additional one or two millimeters. The latter are necessary to ensure that the door frame does not put pressure on the floor covering, due to which the laminate can be deformed. Installation of door frames is always carried out after laying the laminate.

FAQ

Some of the most frequently asked questions regarding interior finishing work.

What comes first, doors or wallpaper?

You can install interior doors both before and after wallpapering. The main thing is not to combine these two works and not to carry them out at the same time. When wallpaper is glued, moisture collects in the room and remains at a high level for up to three days.

The canvases, door frames, and decorative strips swell and increase by about five centimeters. Simultaneous installation of the door will lead to the fact that subsequently, after drying, there will be a large gap between the leaf and the frame. The door lock is also likely to break.

Installation of an interior door

• Good:
  the dust generated during door installation will not settle on top of the wallpaper.
• Bad:
  you will have to spend time and carefully trim, and then tuck the edges of the canvas behind the decorative strip (platband).

• Good:
  during the installation of the door, you can hide all the errors in the plastering work.
• Bad:
  if the dimensions of the doorway are not maintained, and at the time of pasting the wallpaper was cut along the opening, then the platband may not close the resulting gaps.

When to glue ceiling plinth?

Ceiling plinth is a decorative element that serves to delimit and hide the seams between the ceiling and walls.

Ceiling plinths include:

1. baguettes;
2. cornices;
3. curbs;
4. fillets.

Their task is not only to hide seams and transitions between the wall and the ceiling, but also to prevent the formation of cracks.

You can glue the baseboards before and after wallpapering. However, it would be more appropriate to attach them directly to the wallpaper.

All surfaces must be leveled using putty. When it is planned to paint the fillet, this is done immediately after painting the ceiling, before it dries. Otherwise there will be marks between them.

Without painting the baseboards, after waiting until the ceiling is completely dry, you should cover the joints with tape, which will protect the ceiling from glue, and fasten the baseboards. Only then are the walls painted or pasted over, adjusting the edges of the canvas. If you later need to change the wallpaper without touching the baseboard, you can easily remove it. Therefore, it is correct to glue the ceiling plinth first.

If the plinth is glued on top of the wallpaper, then in this case you will have to painstakingly cut everything off or replace it completely, along with the plinth.

When is it better to stretch the ceiling?

Stretch ceilings are a specific product, which makes it possible to install them at the final stage of finishing work. During stretching there is practically no dirt and the likelihood of damaging the finished wall and floor covering is very small. However, experts advise hiring specialists to get quick and high-quality results.

In this case, the top-down principle does not work. It is intended for primarily standard and routine repair work.

Ceiling tiles or wallpaper first?

It is best to glue the ceiling tiles first. In order not to stain or damage the wallpaper in the future, since paint, whitewash, glue and similar substances leave practically impossible to clean marks on them.

Floor or wallpaper: which comes first?

Preparation. The walls need to be prepared only after the floor. The debris is removed and is ready for installation of the final flooring. It is laid at the end of the repair work. Before this, the base is covered with film, so that later traces of plaster can be easily removed.

Laying. All wallpaper is pasted before the linoleum is laid; the wooden floor should also be sanded at the end. However, some craftsmen believe that wallpapering is done after laying the floor and attaching the baseboards. This is due to the fact that the wall decoration can be replaced at any time without touching the baseboards.

What's next, decorative stone or wallpaper?

It also doesn’t matter what you glue first. Basically everything depends on the professionalism of the performer.

If you stick a decorative stone at the beginning, then the wallpaper is simply adjusted and cut off in the areas where it overlaps the stone. Even if there is excess damp fabric left, it will dry and the joint will be invisible. The wallpaper is cut with a painting knife with a thin blade. They are pressed tightly against the stone with a spatula and cut along its edge with a knife. The spatula holds the wet wallpaper and prevents it from tearing.

You can also stick a decorative stone on top of the wallpaper. However, you need to work carefully so as not to stain them with glue. To prevent this, you can outline the boundaries of the future fastening in advance, and stick masking tape on the wallpaper. When finished, the tape is removed and the canvas remains clean.

When is the air conditioner installed?

It is more correct to begin installing the air conditioner before pasting the walls or covering them with plasterboard. Communications connecting two blocks (internal and external) are hidden in the walls. At the same time, the outdoor unit is installed, thereby completing the dirtiest part of the work.

Once the interior finishing is completed, the indoor unit is installed. Its installation takes about an hour, and after that a test run is carried out and the operation of the air conditioner is checked.

Photo wallpaper or wallpaper first?

Initially, it is better to stick the wallpaper, then, joining it, stick the photo wallpaper and again the wallpaper strips. However, in order for the drawing to lay flat and not beveled anywhere, it is necessary to mark the vertical. The vertical is the standard by which the wall is aligned. It is useful for uneven and bumpy walls. This is not necessary, but will help keep the pattern even.

Main Factors

Usually, the decision on what to do first - wallpaper or suspended ceiling - is influenced by the following established, but not indisputable, statements:

1. The floor and ceiling need to be processed last , because “it’s right,” and besides, finishing the walls is too dirty work, you can ruin everything.
2. If the walls are previously covered with vinyl, then the joint between them and the stretched ceiling surface will not be visible.
3. What if wallpaper glue leaves unsightly spots on a clean ceiling?
4. When installing a stretch ceiling, the material is treated with a special heat gun, which heats the coating to 70 degrees. At such a high temperature, the vinyl will melt and change color.
5. When numerous holes are drilled in the walls for fixing the baguettes, the fresh wall covering will be stained with a thick layer of dust.

Examples in the interior

To accurately understand the progress of the work, let’s look at it using the example of finishing a kitchen.

It is necessary to decide on the layout of the room and the interior. You can come up with the interior yourself or select from ready-made works available on the Internet.

Next, the so-called “zones” are designed, for which the necessary materials are already selected. The kitchen should have two “zones” - a working one, where food is prepared, and a dining area. They are usually separated by different facing materials. The working area is decorated with tiles, and the dining area with wallpaper, thus creating a cozy atmosphere. Of course, this is an approximate standardized solution.

For novice builders and home owners who deal with renovations every five years, the question of the sequence of finishing work arises at all stages, because not only the quality, but also the durability of the finishing coating depends on compliance with the subtleties of technology. What comes first: installing doors or hanging wallpaper. The answer to this question is given by experienced builders who have tested both options in practice.

What comes first: wallpapering or installing a door

If you mount the door completely before gluing the wallpaper, difficulties will inevitably arise in matching the wallpaper to the door frames

To decide in what sequence to carry out the finishing work, you should understand how the door frame is structured and what difficulties and risks arise when installing doors:

• doors are installed using polyurethane foam, the excess of which, after expansion and hardening, is cut off and the gaps are puttied;
• if the wall is thick, then slopes appear at the door, which need to be plastered and puttied and only then covered with wallpaper;
• The technology for gluing wallpaper implies the absence of drafts and closed windows and doors, otherwise a tight fixation will not work.

Installing doors is rough work, gluing wallpaper is finishing work.

These factors determine the optimal course of action:

1. Preparing and leveling the wall surface. The use of plaster and putty, primer and impregnation makes this process dirty, the floor will be stained, there will be smears and stains on the ceiling. The best solution is to prepare the walls, ceiling and floor together.
2. Door installation. The platbands are not yet attached. The gaps and slopes around the box are puttied for finishing.
3. Wallpapering all the way to the edge of the door frame. The doors are covered with film and closed until the wallpaper glue dries.
4. Installation of platbands. They cover all the unsightly places and the edges of the wallpaper.

A forced change in the sequence is acceptable: then around the doorway you should leave allowances for the slopes along the width of the wallpaper, or leave the area unfinished, and after installing the door, carefully glue the pieces.

It is necessary to wallpaper walls correctly and competently. In most cases, wallpaper is chosen for wall decoration as the most compromise finishing material. Today, when in two minutes you can find a lot of offers with help in gluing, many refuse the idea of ​​a completely independent repair. But often the fear of doing something with your own hands “from start to finish” is simply far-fetched. Have you ever hung wallpaper yourself? Maybe it's time to start? Just arm yourself with information, prepare from the theoretical side, and then in practice everything will go like clockwork.

Door installation in Saransk

— When to glue wallpaper before or after installing doors?

— When dismantling an old door, chipping of the plaster from the walls is possible, and in 70% of cases it is necessary to increase the opening both in width and height, which can also lead to chips of concrete or plaster that will need to be plastered. It is best to glue the wallpaper after installing the doors. Or do not glue the wallpaper one meter to the left and right of the door. When gluing the wallpaper, you cannot remove the trim, and you also cannot push the wallpaper under the casing. Cut the wallpaper along the edge of the casing with a utility knife.

— How long does it take to install doors?

— It all depends on the dismantling and embedded fittings. On average, installation of three doors (dismantling, additions, cashing on both sides) takes about 9 hours

— Which hinges are best to buy?

— There is no need to save money here, since the door is held on hinges. The thicker the loop, the more difficult it is to bend. And for all doors you should buy the same hinges, both in length and width. There are also hinges, both left and right, you don’t have to worry about this, you need to buy universal ones.

— How do you attach the box to the opening?

— The box must be secured to an anchor in the opening to avoid sagging. We put anchors under the hinges so that they are not visible, plus three hangers on each side.

- Panel house, we are going to do renovations in the bathroom and toilet, where to start?

— Panel houses have very small bathrooms. When installing the door, you will have to make a hole in the bathtub frame; later, when replacing the bathtub, it will be difficult to pull it out and install a new bathtub without damaging the door frame, so if you are going to change the bathtub, it is advisable to install it before installing the doors. Discuss with the tiler in advance about how the doors will be decorated inside with tiles or trim

-Is there a lot of dust and debris when installing doors?

-There will be a lot of dust and debris. It is advisable to cover everything with film in advance. Prepare durable bags for garbage. There will be about two times more dust than when installing windows

-How much space do you need to assemble doors?

-The more space the better, since all the doors are assembled at once. We put all the doors on the racks and start inserting the fittings

-I have a small child. Will he bother you?

-If it is very small, then it will not withstand the noise of tools. Well, if he is already running, then the likelihood that he will get injured is high, since all of our tools are cutting and sawing. In any case, it is necessary to take the children away while the doors are being installed.

— We bought the doors. They installed them for us through an acquaintance, and decided to save money. But they put it in such a way that tears well up... Is it possible to somehow fix them?

- Possibly, but depending on the situation. It is necessary to initially inspect the doors, assess how damaged the door is and count the material (new box, extras, cash).

— How to install doors in a room with or without a threshold?

-installing a threshold in interior doors does not make sense. They installed a threshold in Soviet times, and this was because the doors came already assembled in a box with a threshold. Also, the threshold between rooms is, as they say, a “stumbler.” But I can say about the second entrance and toilet with bathroom are the opposite, where a threshold is desirable, but not required.

— Are the photographs on the site all your works?

-Yes, these are all our works. Only in the category “tools” and “a little about doors” the photo is taken from the Internet

— Do you only install doors or something else?

-We only install doors. Therefore, we keep the quality at a high level. We believe that everyone should do one thing

— How to correctly measure doors and components for them?

— measuring doors requires skills. The best option is to call a measurer, or even better, someone who will install them.

— What is the best way to install suspended ceilings before or after the doors?

— When installing the doors, there will be a lot of dust that will settle on the ceiling, and there is also a chance that the ceiling will be torn by the platband or timber during the assembly and installation of the door. Therefore, it is better to wait a while with the ceiling. and stretch the ceiling after the doors

-Do you work separately or together?

-We work together, which increases the speed and quality of door installation

— Do you work on weekends?

-In most cases, we work on weekends, since not everyone is released from work on weekdays

-I need to install doors, but I don’t need handles and locks. Their husband will then hit them himself.

-No. We don’t put it that way. Assembling and installing a door is a complex and, one might say, jewel-like process, so it is better to entrust the entire installation of doors to professionals.

— My opening in the wall starts from the corner of the room, it turns out that the door will be pressed against the wall perpendicular to the opening. Accordingly, the platband will not fit there, can you cut off the platband along its entire length?

- Yes. We cut the platbands to length. Cases in which the platband has to be “narrowed”: this is when we install doors in panel houses to the toilet and the bathroom (“we narrow” the platbands inside the toilet on the left side, and inside the bathroom on the right side. On the outside there are two platband in the middle between the bathtub and the toilet). when we place the door between two parallel walls (“narrowing” of the casing on the left and right on the inside and outside), etc.

The first and main tip: how to start gluing wallpaper correctly

Let’s say you know perfectly well how to carry out the preparatory work, and you don’t need to waste time explaining this stage. Do you know right away where you will be gluing from - from the door, from the window, or maybe from the corner? Meanwhile, this moment is very important. With this choice, the type of lighting in the room is important.

When, back in Soviet times, almost all wallpaper was glued overlapping, there was such a strip on the wallpaper itself, onto which the new canvas was glued. And so that the transition would not be visible, it was necessary to glue it away from the window.

Today this problem is not so acute. If you are using thick wallpaper, then it is not at all possible, or rather, it is not recommended, to glue it overlapping.

There are several options for where you can start gluing wallpaper indoors.

Where to glue from, options:

1. From the door. The main thing is to maintain strict verticality, so you can start work from any vertical landmark convenient for you. This could also be a door frame. Glue the very first canvas strictly vertically, so it would be a good idea to use an additional device such as a plumb line. Then gluing continues in the chosen direction.
2. From the corner. The method will only be good if the room has perfectly even corners. But this doesn’t always work out that way, so it’s more common to glue from the door or window.
3. From a major landmark. If there is more than one passage and more than one window in the room, the pasting process begins from the largest landmark.
4. From several equal lines at once. This method is good for a room with a large window, then pasting is carried out in different directions from this same window. And to make the joints less noticeable, they are made above the window or above the door.

Please note: if the corners in the room are uneven, no matter how exactly you glue them, verticality is lost. Therefore, in this case, when pasting each wall, you need to use a new vertical line. It's troublesome, but there's no other way.

What to do first: glue wallpaper or lay laminate

22.01.2017

Every time we tidy up the interior of an apartment or house, we are faced with the need for cosmetic repairs. This, in turn, requires a fairly thoughtful layout. What comes first, wallpaper or laminate - this question interests many of those who are thinking about carrying out renovation work.

Advantages and disadvantages of different methods

Of course, there are many different opinions regarding what came first, wallpaper or laminate. Representatives of different repair teams, and in general, specialists in the field of repair and construction may have different points of view on this matter. However, each method has both obvious advantages and certain disadvantages. Let's look at all the necessary questions in more detail and provide some tips regarding laying flooring and designing wall decoration.

Meanwhile, a very important criterion that affects the order of work is what kind of garbage and in what quantity remains on the floor, walls, ceiling, and so on. The fact is that leftover building materials can significantly complicate subsequent work. It is for this reason that it is first recommended to carry out that stage of repair that will result in as little contamination of the surrounding space as possible.

On a note! When laying flooring (be it parquet, laminate, linoleum or any other type of flooring), the level of debris, dust and dirt that can get onto other surfaces is minimal.

You need to think carefully about what happens during the repair and what the step-by-step mechanism of action as a whole consists of. This will help you draw logical conclusions about whether wallpaper or laminate does first. Here are the circumstances that are important:

Laminate floors, unlike other types of surfaces, such as, say, linoleum, carpet and some others, do not need to be “adjusted” to the wall. Thus, the wallpaper (if it is already pasted) will not be damaged. Laminate flooring, as you know, is mounted with special spacer wedges at a certain distance from the wall. In addition, the possibilities for the appearance of certain types of contamination when using this type of floor covering are minimized. Of course, this becomes possible provided that all necessary steps regarding preparation are fully followed. They must be completed in advance, even before laying the floor or gluing wallpaper to the walls. When laying the floor, as a rule, a lot of dust and debris is not generated

When laying the floor, as a rule, a lot of dust and debris is not generated

On the other hand, any technology has certain disadvantages. Even in the case under consideration, a situation may arise in which certain types of laminate will show excessive sensitivity to glue fumes and, in general, to the high level of humidity that occurs when wallpapering in a room.

Attention! If you decide to reliably protect the laminate floor during other stages of repair, then it should be covered with plastic film or similar coverings. By the way, the floor should be covered with film regardless of what comes first: wallpaper is glued or laminate is laid, and for this reason. The fact is that almost all modern wallpapers (vinyl, paper, non-woven, etc.) dry well only in the complete absence of drafts and, as a result, with the windows closed. Accordingly, the humidity level in such a room increases sharply. It turns out that moisture in the form of evaporation (atmospheric) can have a negative effect on the laminate for several days. The outer layer of the laminate, especially if we are not talking about the most moisture-resistant classes, may suffer somewhat.

However, this is only possible with regular re-gluing of the canvases, which would be carried out every year, or even more often. If you don't plan on this, then don't worry.

Is it possible to glue wallpaper after laying laminate flooring?

Talking about whether it is worth gluing wallpaper or laying laminate first, you need to say a few words about this option, in which the floor covering is laid first. Of course, it is technically possible to lay the floor first, and only then start gluing the wallpaper - you can. However, this is not recommended for one simple reason: the outer layer of the laminated coating may become dirty, or even completely damaged due to exposure to it during subsequent wallpapering.

Therefore, despite the fact that this option is also possible, most professional specialists who work in the field of repair and arrangement recommend that the first thing you do is decorate the walls. In any case, if you were not aware of when to lay the laminate before or after the wallpaper, and the first thing you did was lay the flooring, don’t worry. As noted above, you can always provide the floor with additional protection by using plastic film or other similar protective coatings.

On the other hand, it is also worth paying attention to protection from other factors. Examples include such things as legs from pieces of furniture (chairs, tables, cabinets, and so on), supports from a small home staircase or scaffolding that are used in renovations, and much more. In such cases, film, as a rule, turns out to be powerless and you will have to use something stronger and more reliable.

Step-by-step instruction

So, with regard to the sequence of what comes first, wallpaper or laminate, it should be understood that repair work has its own rules that must be followed based on a certain sequence of stages. As a rule, the first thing is wallpaper. Laminate (just like other floor coverings, including parquet, natural floor boards, and so on) is laid after. Let's briefly look at the main steps that should be performed step by step:

First, the walls are completely prepared before gluing roll wallpaper or applying liquid wallpaper (they are more reminiscent of decorative plaster. We arrange the screed and, if necessary, make a so-called subfloor. After this, you need to glue the wallpaper, following the appropriate instructions. When the glue is completely dry, you can gradually move on to installing the floor.You need to lay it at the very beginning, and only then install the baseboards and other related decorative elements.

Conclusion

Of course, everyone has their own opinion about how to properly make repairs and, in relation to the specific situation under consideration, about whether wallpaper or laminate comes first. Be that as it may, the first method, which involves the initial design of the walls, and only then the arrangement of the floor, looks more preferable due to quite objective reasons. All of them were discussed in more detail in the article. On the other hand, one cannot be completely categorical and unequivocally state that the first option is the only correct one, since everyone may have their own arguments regarding what is done first - wallpaper or laminate. In any case, good luck with your interior redesign!

sledcomspb.ru

Which is better: to glue wallpaper from the window or to the window

It doesn’t matter whether you start gluing wallpaper from the window or from the door. Maybe you even wallpaper a room with perfectly straight corners (which is extremely rare). The main thing is to glue the wallpaper from a perfectly level vertical. If the first canvas is placed evenly along a vertical line, then all subsequent canvases will go smoothly.

You should start gluing wallpaper from a perfectly flat vertical line.

Therefore, most often paper, vinyl and non-woven wallpaper are glued away from the window. It’s more common this way, and they also hope for the evenness of the window opening. Therefore, the window is used as an ideal vertical from which the walls are finished in order to achieve even lines. But the door can also be such a starting point; this is by no means a mistake.

What to put first and where to start gluing wallpaper in the room

If the renovation is in full swing, and you still don’t know what to do first – lay the floor or glue the wallpaper? Professionals advise doing the things that leave the most waste first. Laying linoleum is unlikely, but laying laminate might be better first.

In the room where renovations are being carried out, all work is completed first, after which more garbage remains

If you first glue wallpaper and then lay laminate:

• Some types of laminate are very sensitive to wallpaper glue, so the coating can deteriorate, which means everything is correct, stick it first;
• Construction debris can also theoretically damage the laminate;
• If the laminate is already laid, protect it with a special film from the work being carried out.

In the case of linoleum, wallpaper is usually glued, and then the linoleum is directly laid. But still, do everything with an eye on the individual characteristics of the repair. And what is more pleasant and habitual for you to do. Adapt to yourself, there are no strict rules.

Advantages and disadvantages of installation

If you still decide to cope on your own, you need to decide what to do first: lay the floor or hang the doors. This question is often asked by beginners when making repairs, because each possible path has its pros and cons.

First of all, it should be noted that the installation of floors in any case is carried out after wallpapering or other wall finishing. Otherwise, they will quickly be damaged by traces of plaster, paint, and covered with scratches from careless handling during repairs.

This is the main dilemma of repair

: If you lay the floors before the doorway is installed, the laminate flooring will most likely be damaged. But at the same time, it will be much more convenient to take measurements and hang the door, knowing exactly what the final result will be.

You can first install the doorway. But then you will need to carefully decorate the threshold so that it looks aesthetically pleasing and unnoticeable.

In addition, you may not guess the height of the door, then it will have to be removed and filed, which, of course, is inconvenient.

How long does it take for wallpaper to dry?

Non-woven vinyl wallpaper, so popular today, takes a day or two to dry. The drying speed depends on the microclimate in the room, on the type of walls and wall coverings, on the density and thickness of the wallpaper. And also, of course, on the quantity, quality and thickness of the glue.

Wallpaper dries depending on the type, as well as on the amount and thickness of glue

The higher the temperature in the room, the faster the wallpaper will dry. If the room is below plus ten or seven, it is not recommended to glue wallpaper at all. Likewise, temperatures above +25 are also not recommended for repairs.

Which is laminate or interior first? What should come first during renovation: wallpaper or doors?

Fitting laminate flooring around doors when they are already standing is the hardest thing to do. Especially if you are not an expert. You can break the locks and cut the slats incorrectly.

The finishers (according to their words) don’t care what happened before – laying laminate flooring or installing a door. Depending on what is done first, the master takes into account a number of features.

It is very important to take accurate measurements in the doorway. A door with a threshold has its own characteristics. And if the laminate has not yet been laid, its thickness matters.

After studying the builders’ recommendations, we’ll figure out what to do first when making repairs. You will learn what to pay attention to when laying laminate flooring and installing doors. This is important so as not to damage the new floor and door leaf.

When can you open windows after wallpapering?

The time you need to wait before opening the window after the gluing process is no less than 12 hours. Sometimes you shouldn’t open the windows for a whole 48 hours. Wallpaper dries at a constant temperature, it should not be lower than +15. And the so-called wandering drafts can ruin all the work.

After the wallpapering process, windows can be opened no earlier than 12 hours later

Also, for the first days after gluing, try not to drill, install or turn on the air conditioner. Stretch ceilings are also not installed the first five days after gluing. However, the installation of ceilings involves strong heating, which is unacceptable at the moment.

How to start gluing wallpaper correctly (video)

Wallpapering is a more difficult process psychologically than physically. If you don't rush, if you follow all the rules, if you choose good material, then even beginners can do this job perfectly. That's what we wish for you!

Happy sticking!

The question of where to carry out repair work first - on the walls or ceiling - has been asked since the advent of tension films.

You really don’t want to dust off the fresh gloss that reflects the entire room. It’s also a pity for expensive wallpaper if it suddenly gets damaged while working with the stretch fabric. To understand this issue, we will try to follow the process of repairing ceilings and walls step by step.

Process Features

Whatever work has to be done first, each will be to the detriment of the other. When installing a baguette under a stretch fabric, holes are drilled in the wall, which produces a lot of dust, and fresh wallpaper can be damaged. In addition, the installation of the canvas itself involves high temperatures. No one knows whether the wallpaper will like it.

There is a way out. Carefully prepare the walls for pasting and invite specialists to install the baguette (do the most dusty work), then paste the wallpaper

and again invite workers to install the ceiling. The method is good, but there is one problem - the craftsmen will not agree to such a lengthy method of work.

To understand the features of the process, and at least get closer to figuring out what to do first, you need to try to figure out what a suspended ceiling and wallpaper are.

The canvas itself is a fabric base or a PVC product, which can be matte or glossy. Installed on a specially prepared metal or plastic frame.

If the ceiling was planned to be multi-level, all work with plasterboard should have been carried out in advance

. First, the old finish is removed, the ceiling is cleaned well, otherwise in the future finishing debris will fall onto the tension fabric. Then it’s time to treat fungal stains (if any). Before installing the ceiling, all electrical work must be completed.

Wallpaper is a roll of various types: paper, non-woven, vinyl. Many people had to glue them. To begin with, the walls are leveled, and a layer of glue is applied to the dried surface (if the wallpaper is paper, the glue is also applied to the canvas). Then the coatings are placed on the base, glued well, and air bubbles and excess glue are squeezed out with a roller.

There is nothing complicated about this, but there are two types of developments: either the wallpaper is pasted in front of the ceiling installation and pressed down with a baguette (in this case they look neat), or after that the top of the canvases will have to be carefully trimmed, trying not to damage the ceiling structure.

Advantages and disadvantages of each option

Before you decide what you will do first - install the door frame or lay the flooring, you need to have a good understanding of the essence of the issue. The advantages of laying the flooring before installing the door frame are the following:

• nothing puts pressure on the laminated panels and does not prevent them from “floating” freely;
• When the finished floor is completely ready, measurements for making the door leaf will be most accurate. In this case, you will not have to shorten it if necessary, which means that you will avoid unnecessary waste of time;
• the cost of work in the case when the laminate is laid first, and then the door frame is installed, is lower, since you do not have to force the floor covering under the door frame (which can damage the material, and you will need to purchase it additionally), or carry out work to correct its size.

The only drawback of this method is that there is a risk of scratching the floor covering during the installation process. However, you can avoid such troubles quite simply - just cover the floors with a soft cloth and lay polyethylene on top of it. In this case, nothing will threaten the laminate.

Proponents of the method in which the door frame is first installed, and then the floor is laid - or, if we are talking about cases where there is no need to change the previously installed door frame - its advantage is the complete elimination of the risk of damage to the floor covering.

The disadvantage is the higher cost of the work, since most likely you will have to adjust the height of the door leaf to the floor covering. In the case of paneled canvases, most often, this option is not applicable at all.

Professionals recommend laying laminated panels on a special substrate, which insulates them from contact with the previous coating, acts as insulation and has soundproofing properties. In this case, the floor height will rise by at least one centimeter. This may prevent the door leaf from opening and closing freely.

In such a situation, you will need to saw off the bottom of the door frame: this is done using a special hacksaw with an offset handle. There should be a gap of such a size that the laminated panel fits freely into it, and the racks of the box do not put pressure on it. In the case where the slopes are finished with extensions, you will also have to shorten them taking into account the height of the selected covering.

If for some reason it is impossible to change the height of the door leaf, you will first need to completely get rid of the old floor covering, after which you can lay the laminated panels.

They are laid in such a way that there are small (about 0.5 centimeters) gaps between the wall and the outer elements of the covering. Subsequently, they are covered with baseboards. If different types of flooring are laid between rooms, you need to leave a small damping gap between them, which you will then cover with a special profile.

When the door leaf has already been installed, during the installation of laminated panels it must be protected from dust and possible mechanical damage. To do this, cover the door leaf with plastic film, and cover its outer elements with masking tape. It should be remembered that with each of the listed methods, the platbands must be removed, and after the work is completed, they must be installed and adjusted in height.

What is the sequence?

Let's try to understand what is better: to stretch the suspended ceiling before or after wallpapering. To do this, consider both options.

First the wallpaper, then the ceiling

If you decide to act in this way, it is worth considering the need for a break of 4-5 days between pasting the walls and installing the ceiling. The wallpaper must dry well before the heat gun works.

.

Some experts believe that you should first work with the walls and align them perfectly, otherwise the ceiling panel may be skewed.

The main danger of pre-gluing is contamination of the walls when working with a hammer drill.

If traces of brick remain on the wallpaper, it will be quite difficult to remove them.

A rotary hammer equipped with a vacuum cleaner would help solve this problem to some extent. Gluing the canvases before installing the ceiling frame will result in them getting under the baguette. It will press down the top edge of the canvases, which will make it difficult to dismantle the wallpaper during the next repair.

. The positive thing is that the top contour of the wall is perfect.

You can opt for liquid coatings

. They are beautiful and modern, but the risk of staining the finished ceiling when working with a spatula increases.

If you have to glue wallpaper for painting, the risk of staining the ceiling becomes even greater. On the other hand, high temperatures during installation can affect the quality of the paint at the base of the ceiling. The same problem can happen with liquid wallpaper.

First the ceiling, then the wallpaper

If the wallpaper is light and delicate, it may be irreparably damaged during the installation of a stretch ceiling, so it is better to paste it over at the last stage of repair. In addition, a lack of professionalism among those working with the ceiling can lead to mechanical damage to the wallpaper.

When gluing walls, you should work carefully with the upper edge of the canvases so as not to disturb the ceiling plugs

. Everything will work out if you show diligence, but during the next repair the wallpaper can be easily dismantled.

Both options have their pros and cons, but responsibility for the choice always lies with the owner.

What do you do first: doors or wallpaper?

To other news

What do you do first: doors or wallpaper?

June 23, 2019

During a major home renovation, the question often arises of what to do first: doors or wallpaper? Masters have different approaches. Therefore, we have collected the pros and cons for each option. You just have to choose what is more convenient in your situation: first, wallpaper or interior doors.

Features and advantages of the “interior doors first” method

Installing an interior door is a dirty job. Logically, it needs to be done first, and only then proceed to finishing the walls. That's why many masters choose this method.

There are compelling advantages in its favor:

• there is no risk of damaging or staining the wallpaper, so door installation is faster
• dust will not settle on the finish
• When there are doors in the room, it is easier to protect freshly pasted wallpaper from drafts.

This method also has its own characteristics:

• It will be inconvenient to glue wallpaper near door frames: you will have to trim the wet sheet and this will not be easy to do
• It is believed that moisture from the wallpaper may cause doors to swell.

For many, these are strong arguments in favor of the second method.

Advantages and features of the “wallpaper first” method

Those who have had to do repairs themselves know perfectly well how difficult it is to align the wallpaper around the door or tuck the edge of the canvas under the trim. Therefore, they will prefer to paper the walls even before installing the interior door.

The second argument in favor of this method is the risk that the door will become deformed from the moisture released by the drying wallpaper.

Features include:

• dust that accompanies door installation
• risk of potholes on the wall next to the door frame - the wallpaper will have to be re-pasted
• the likelihood of the new wallpaper being splashed with solution when leveling the slopes
• Some craftsmen recommend peeling off the wallpaper around the perimeter of the doorway so as not to spoil the canvas.

conclusions

As you can see, each method has its pros and cons. And advantages in one situation may be disadvantages in another. Therefore, there is no clear advice on what to do first: wallpaper or doors. Just take all these points into account and decide what is more convenient for you.

However, if interior doors are installed by professionals, the likelihood of undesirable consequences is sharply reduced. That's why we suggest using. Experienced craftsmen will tell you how best to proceed in your situation and will do the work quickly and accurately. Contact us!

To other news

Important nuances

The issue of order has not yet been clarified. What to do first, install suspended ceilings or work on the walls? Wallpapering, as well as installing a ceiling, have their own nuances. When working with walls, there is a chance of damaging or staining the stretch fabric, but it is virtually eternal, while wallpaper can be re-pasted every year.

When a profile is placed under a suspended ceiling, there is a possibility of contamination of the wallpaper, and there is also a fear that it will not withstand high temperatures. In this case, you can abandon the polyvinyl chloride surface in favor of a fabric canvas

, which is mounted using a cold method.

And one more nuance - the profile for a woven ceiling requires shallower drilling, which means there will be less dust. However, well-dried wallpaper can easily withstand temperatures of 60-70 degrees.

The PVC film needs to be heated to soften it. The prepared canvas is immediately tucked under the profile using special tools. The gap between the material and the wall is masked with plugs. They are the first to suffer from poor quality wallpaper work.

An important nuance: any suspended ceiling can be installed in the presence of wallpaper, even in a room furnished with furniture. Sliding wardrobes and curtains are also not a hindrance to this process. You'll just have to use a vacuum cleaner afterwards. But, if the renovation has just begun, you need to ask yourself many times what to do first.

But what if the renovation was done a long time ago and you need to re-stick the wallpaper without damaging the ceiling? Dismantling should be carried out very carefully, especially if the wallpaper was pasted at the initial stage

and fell under the ceiling profile. They will have to be released without damaging the canvas.

To complete the work you will need a spatula and a construction knife. Carefully insert the spatula between the ceiling and the knife. Moving them along the walls, slowly cut off the old wallpaper. In this way, you can protect the material from being cut, even if the knife comes off.

It is much easier to remove the finish if you wet the walls with water and wait a while.

After studying the workflow, we expected to immediately get an answer to our dilemma. There is no answer, you will have to turn to specialists.

Experts' opinion

The renovation is coming to an end and it is hoped that experts will shed light on the sequence of construction work.

Craftsmen believe that it is better to cover the walls and then install the ceiling

. The arguments are the same: there is a risk of damaging or staining the walls; in addition, high temperatures are unfavorable for fresh wallpaper. Perhaps these craftsmen are afraid of responsibility for the dusty walls.

Other experts, on the contrary, advise installing the ceiling after gluing, fearing for the canvas

, which can be damaged with a construction knife when cutting wallpaper. And glue and paint getting on the canvas will ruin it forever.

There is no clear opinion even among professionals, because the material for work, the premises, various nuances - everything can be extraordinary, requiring an individual approach.

Successful examples and options

In conclusion, I would like to dwell on the aesthetic component of the work done. If you see how beautiful the ceilings and wallpaper have become, the answer to the question of what to do sooner may emerge by itself. Or it may not work out.

Stretch ceilings have always been an interior decoration. It can be amazing and mysterious, like a country through the looking glass. With it, the room is filled with colors, it seems larger and brighter. Ceilings come in different types and have their own design and style.

Matte

Absolutely flat surface without a hint of reflection. The texture resembles a classically painted canvas. Used for large rooms

.

The matte finish is so neutral that it suits any style. Soffits will be good equipment for the ceiling

, or other sources of bright light, because the matte canvas does not reflect light.

Glossy

A good option for small rooms. They get the opportunity to visually double in size. Moreover, the dark gray fabric has a stronger reflectivity

.

Spotlights (even with a weak glow) on such a ceiling look like stars. By building multi-level compositions using plasterboard and placing a canvas in them, they achieve the effect of an almost natural image of water or sky.

Fabric

Despite its textile origin, the fabric is still processed with polymers and acquires special strength.